That's ok though, there are other systems in the area that work. FLA Member. This may help too. Joined Apr 22, Messages 3. I read these articles and the manual and I'm still having trouble. The part I don't get is how to know what to enter in each tgid for an ltr system. I read the database on here but it doesn't look like the right format. I would except one frequency and a lit of tgids.
Am I totally lost? Any tips are greatly appreciated. These are the little details that seem insignificant, but can stop you from making things work. So, how do you know if it's trunked when you hear the transmission? Also, do you hit function, Trunk? Or just the trunk key? Deleting Saved Frequencies To delete a saved frequency: To delete all saved frequencies in a bank: Page Scanner Cloning transmissions operate independently of each other.
Use FM mode for mixed analog and digital voice transmissions. Page Searching The. To clone the scanner data: Page Search Banks display.
Search Banks To search preprogrammed search banks: Safety Aircraft Amateur. Bands Railroad Limit. Zeromatic While. Page Programming A Search Range frequency.
To activate Zeromatic: Page 22 advantages. Stalker II searches in finer steps until the signal source. To use Signal Stalker II: Locking Out Frequencies When. Page Saving Found Frequencies The first locked- out. To unlock all frequencies in a search bank: Saving Found Frequencies To save a frequency found during a search: Page Scanning Scanning Scanning.
To scan: Locking Out Channels You. To locked out a channel: Page Priority Scanning To review all locked out channels: When you finish reviewing locked-out channels,. You can manually select any channel in a bank, even in turned-off banks.
Priority Scanning In. Page Weather Alerts To make an existing channel a Priority channel: To modify the Priority channel: Page Same Standby Mode the. To perform a weather scan: Press. To program a weather channel into priority channel: Page 29 Code County. County To review stored FIPS codes: The scanner sounds an alert or beep when it receives the SAME code. The scanner searches the weather frequencies while SAME standby mode when squelch is off. To test the weather alert: Page Monitoring To use Skywarn: Hold.
Monitoring When. To monitor a channel: Page Trunking Setup To set a default tuning frequency: Trunking Setup Instead of transmitting on a specific frequency, trunking. Defining a Trunking Bank You can define any of the 10 banks as a trunking bank,. To set Open or Closed mode for a bank: Motorola Trunking Setup Motorola systems can allocate as few as five frequencies. Page 34 Fleet Maps For. To program a fleet map: Base and Offset Frequencies To. Page Edacs Trunking Setup M and the bank and channel number appear.
Press PGM. M changes to P. Use the number keys to enter the frequency including the decimal point. If you make a mistake, press CL to delete a single digit or hold CL about 2 seconds to start over.
Your scanner automatically rounds to the nearest valid frequency. For example, if you enter If necessary, press MODE to change the receiving mode. Go back to step 5 again. When you copy a frequency, all the channel conditions, including mode, are also copied. Press TUNE. Tune the frequency you want to copy. To select a new bank, press the bank number.
Press FUNC. Press CL. Use the number keys to enter the bank number. Press 1 to clear all. Any other key aborts. Use FM mode for mixed analog and digital voice transmissions. Enter a conventional frequency. You can also upload or download the programmed data to or from a PC using an optional USB cable and application software available through your local RadioShack store.
The application software is also available online at www. Press 1 to send the data to the other unit or press any other key to cancel. To exit the clone mode, remove the cable. You can search for transmissions using the preprogrammed search bank, which is divided into eight search bands.
When Seek Search is active, the scanner stops on active frequencies for five seconds and then resumes searching automatically. Press FUNC then 7. SR3 to SR5 banks contain several groups. To turn off a group, press the group number; the group number disappears. To turn the group back on, press the group number again. Adjust the Squelch. After the set delay, the scanner starts searching. When the scanner finds an active frequency, it stops searching.
To pause while searching, press PSE. To resume, press PSE again. For more information, see Locking Out Frequencies While searching, the scanner stops if a transmission triggers the squelch setting. However, search intervals smaller than that can stop your scanner short of the correct center frequency. When active, Zeromatic automatically tunes to the. Press FUNC then 0. L blinks for the lower-limit of the range.
Use the number keys to enter the lower-limit frequency including the decimal point. U appears. Use the number keys to enter the upperlimit frequency including the decimal point , then press ENT. Press SRCH to start searching.
Signal Stalker II provides a powerful tool to rapidly detect, monitor and save frequencies of nearby or high-power transmissions. Signal Stalker II resembles more expensive portable frequency counters, but provides many.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox.
Please check your email for further instructions. Enter a new password. Contents Your Scanner Contents Trunking Setup ATT — Attenuator. SRCH — Search. PGM — Program. ENT — Enter. Connecting the Antenna To connect an external antenna, always follow the installation instructions supplied with the antenna. To attach the supplied antenna: 1. Warning: Use extreme caution when installing or removing an outdoor antenna.
0コメント